3 X 3 Stainless Steel Plate-manufacture,factory,supplier from China

Production process:Stainless steel checker plate is divided into two categories:One is rolled by a rolling mill in the production of stainless steel by a steel mill. The thickness of this type of product is about 3-6mm, and it is in the state of annealing and pickling after hot rolling.

At present, there are few cases of large area stainless steel curtain wall in the field of building exterior wall. Even if large area is adopted, it often does not pursue its high flatness, but only expresses strong texture.For The Chicago Cloud Gate project, each individual steel plate was CNC machined at the factory, cut with a stainless steel plasma torch 3/8 inches thick, and molded using a coil machine created specifically for the project.

Spec ChartsType 304Hot Rolled, Annealed and PickledThickness and WidthWeight Lbs. per Sq. Ft.Weight Lbs. per LengthLength3/16 x 488.579343.1610'1/4 x 4811.16357.128'1/4 x 4811.16446.4010'5/16 x 4813.75550.0010'3/8 x 4816.50660.0010'1/2 x 4821.63865.2010'5/8 x 4826.831,073.2010'3/4 x 4832.121,284.8010'1 x 4842.671,706.8010'1 1/2 x 4863.342,533.6010'

How to identify the quality of stainless steel sinks?1. Thickness of water tank steel plate: The high-quality water tank adopts imported 304 stainless steel plate with a thickness of 1mm, while the ordinary low-grade water tank adopts 0.5mm-0.7mm. The method of identification can be determined from the weight and whether the surface is flat.2. Anti-noise treatment: The bottom of the high-quality sink is sprayed or glued with rubber sheets and does not fall off, which can reduce the sound caused by the impact of the water from the faucet on the bottom of the basin, and play a buffering role.3.

1, Corrosion resistance, non-flammable, non-toxic and tasteless.  2, Good wear resistance, long service life, stainless steel perforated mesh wear resistance for ordinary sieve plate 3 to 5 times, for ordinary rubber sieve plate more than 5 times.  3, The total cost is low, although the same specification (area) of stainless steel perforated plate than ordinary sieve plate high one-time investment (about 2 times), but because the life of stainless steel perforated plate is 3 to 5 times the ordinary sieve plate, and less maintenance and replacement, so the total cost is not

Specification of Stainless Steel Sheets, Plates & Coils Specifications : ASTM A240 / ASME SA240Thickness : 0.1mm to 12 mm ThkSheet/Plate Size : 1000 mm x 2000 mm, 1220 mm x 2440 mm, 1500 mm x 3000 mm, 2000 mm x 2000 mm, 2000 mm x 4000 mm.Coil Width : 1000mm, 1219mm, 1500mm, 1800mm, 2000mm, 2500mm, 3000mm, 3500mm etc.Coil Length : 2000mm, 2440mm, 3000mm, 5800mm, 6000mm etc.Surface : 2B, 2D, BA, NO.1, NO.4, NO.8, 8K, mirror, checkered, embossed, hair line, sandblast, Brush, etching.Finish : Hot rolled (HR), Cold rolled (CR), SATIN (Met with Plasti

Type 304Hot Rolled, Annealed and PickledThickness and WidthWeight Lbs. per Sq. Ft.Weight Lbs. per LengthLength3/16 x 488.579343.1610'1/4 x 4811.16357.128'1/4 x 4811.16446.4010'5/16 x 4813.75550.0010'3/8 x 4816.50660.0010'1/2 x 4821.63865.2010'5/8 x 4826.831,073.2010'3/4 x 4832.121,284.8010'1 x 4842.671,706.8010'1 1/2 x 4863.342,533.6010'

304S31 & 304S15 (1.4301) A2General purpose non-magnetic stainless steel possessing good weldability, formability and general corrosion resistance.Bar-rolled edgeRod - BS970 pt 3 BSEN 10088-3Angle - BS970 pt 1 BSEN10051Square - BS970 pt 3 BSEN 10088-3Sheet - BS1449 pt 2 BSEN 10088-2 (2B surface finish)Excellent material for polishingSuitable for food and dairy processing equipment, laundry and chemical industry, process plant and tanksSpecificationsAttributeValueBrandRS PRODensity8 g/cm³Length500 mmTensile Strength520 MpaColourSilverFormSolidWidth300 mmThermal Conductivity16.2 W/m at 100°cM

The 2mm thick braided stainless steel plate is made of austenitic SUS316 stainless steel, and the partition is mostly 500mm x 4500mm. The panel is fixed to the aluminum alloy subframe by tapping nails, and then assembled by the aluminum alloy subframe and the unit mullister to form a stainless steel unit system. The calculation of the panel support system is analyzed according to the large deformation theory.

Precautions when installing stainless steel elbows:  1. When installing, the stainless steel elbow can be directly installed on the pipeline according to the connection method, and installed according to the position of use. Under normal circumstances, it can be installed in any position of the pipeline, but it needs to be sealed to prevent leakage and affect the normal operation of the pipeline.2. When the stainless steel elbow ball valve, globe valve and gate valve are used, they are only fully open or fully closed, and should not be used to adjust the flow to avoid sealing.3.